Skip to content
Cut List Ledger

Cut List Calculator

Plan cuts from the plywood or lumber you have. Account for saw kerf, lock grain-sensitive parts, and print the placement for each stock piece.

Use decimals or fractions such as 1/8. Every measurement uses the selected unit.

Stock sheets or boards

List each usable size and quantity. Include the species or thickness in the material name.

Parts to cut

Use the same material names as the stock list. Lock a part to keep its length aligned with the sheet length.

Measurements stay in this browser.

Calculate the current inputs before printing.

Turn measurements into a cut plan

Read the sheet cutting guide

Start with usable stock

Measure the sheets or offcuts you plan to cut. Enter the width, length, and quantity for each material and size. Two sheets with the same wood but a different thickness should have different material names so the calculator keeps those parts separate.

If a sheet has a damaged or uneven outer edge, measure its usable rectangle or set a trim allowance. The trim field reserves the same amount along all four outer edges. Use a separate stock row for a rectangular remnant that has already been squared and measured.

Read a cabinet example before entering your own job

The cabinet example starts with 48 by 96 inch birch sheets and ten parts. It includes identical sides, top and bottom panels, doors, shelves, and a back. The sides and doors keep their specified orientation. Change the stock quantity or increase the kerf to see how the available material affects the result.

The plan groups the stock by size and material. Sheet drawings put the length across the page. Open the labels and positions below a sheet to find any individual piece from the drawing.

Use long stock for a lumber cut list

For lumber pieces of the same width, enter that shared width for the stock and the parts. Lock orientation and leave enough room between lengths for your kerf. The lumber example fits two 48 inch pieces across two 96 inch boards at a 1/8 inch kerf. One board would fit both only with zero kerf or greater usable length.

Read the lumber cut list guide to compare the recommended stock count and unplaced list.

Check the reason for every missing piece

A missing material usually means a name in the parts list does not match a name in stock. A part that cannot fit may need a larger sheet. A part can also fit by itself yet run out of stock after other pieces have been assigned. Start with the explanation the calculator gives before ordering another sheet or reducing a measurement.

The layout compares several variations of a rectangular packing heuristic. It tries to place all the parts while reusing open sheets. It respects the allowed rotation, matching materials, edge trim, and saw kerf you enter. An alternate layout might use less stock. Check dimensions and the cut sequence on the actual stock before cutting.

Take the plan to the workshop

Download a CSV when you need to check coordinates, count pieces, or share the job with someone who uses a spreadsheet. The export labels placed and unplaced pieces separately. X and Y refer to the original sheet corner with X along the sheet width and Y along the sheet length. The picture turns the sheet so its length reads left to right.

Select Print plan / Save PDF for the material summary and sheet drawings. If you edit an input, calculate again before exporting. Read the sheet cutting guide for a job setup walkthrough or the saw kerf guide for a worked example.

Cut list calculator questions

How does the cut list calculator account for kerf?

It leaves the saw kerf between neighboring pieces. Edge trim reserves a separate amount on every outer edge of every sheet. If two parts exactly fill a sheet with zero kerf, a positive kerf can make one of them unplaceable.

Can I keep the grain direction on cabinet doors?

Check Lock orientation on the door part row. The part’s entered length stays aligned with the sheet length. For a whole project with directional materials, turn off Allow rotation.

How do I plan a job with more than one material?

Add a stock row for each material or sheet size. Use the same material names in the parts list. The calculator will never place a part on a differently named material.

Why are some pieces unplaced?

The calculator reports pieces when no stock matches their material, their dimensions cannot fit any matching sheet, or every listed sheet and usable offcut is exhausted. Check the unplaced list before printing.

How do I print the diagrams or save them as a PDF?

Select Print plan / Save PDF and choose your printer or Save as PDF. The print view starts with a material summary and follows with one drawing per used sheet. Use the printed dimensions to check your job.

Does the calculator find the absolute minimum number of sheets?

It compares several cutting heuristics and shows the best plan it finds. A different arrangement could use fewer sheets. The result is a dimensioned layout and does not prescribe the sequence of cuts.

Can I enter measurements in both inches and millimeters?

Choose a single unit for a plan. Enter inches or millimeters and use decimals or simple fractions. Changing the unit converts the values already entered, then asks you to recalculate.

Can I calculate cuts from long narrow boards?

Yes. Use a stock row with the board’s actual width and length. Make parts the same width and lock orientation. Try the lumber example to compare one or two 96 inch boards with a 1/8 inch kerf.